Home > Community > Forums > PCB Design > How to get the padstack's informations?

Email

* Required Fields

Recipients email * (separate multiple addresses with commas)

Your name *

Your email *

Message *

Contact Us

* Required Fields
First Name *

Last Name *

Email *

Company / Institution *

Comments: *

 How to get the padstack's informations? 

Last post Sun, Jun 3 2007 10:48 PM by archive. 4 replies.
Started by archive 03 Jun 2007 10:48 PM. Topic has 4 replies and 782 views
Page 1 of 1 (5 items)
Sort Posts:
  • Sun, Jun 3 2007 10:48 PM

    • archive
    • Top 75 Contributor
    • Joined on Fri, Jul 4 2008
    • Posts 88
    • Points 4,930
    How to get the padstack's informations? Reply

    How to get the padstack's information like as: Begin Layer, End layer, soldermask and pastemask, etc? with one command.
    Is there any skill file to run the same?
    How to measure air gap between solder mask pin to solder mask pin?


    Thanks in advance,
    Regards,
    SATYA
    ATS ECAD


    Originally posted in cdnusers.org by satya1234
    • Post Points: 0
  • Sun, Jun 3 2007 10:58 PM

    • archive
    • Top 75 Contributor
    • Joined on Fri, Jul 4 2008
    • Posts 88
    • Points 4,930
    RE: How to get the padstack's informations? Reply

    hello satys,

    regarding 1st query I dont think there is any option right now.

    But for second one you can activate measure command and in option tab select

    class - Pin
    Subclass - Solder mask *


    Originally posted in cdnusers.org by eswar
    • Post Points: 0
  • Sun, Jun 3 2007 11:03 PM

    • archive
    • Top 75 Contributor
    • Joined on Fri, Jul 4 2008
    • Posts 88
    • Points 4,930
    RE: How to get the padstack's informations? Reply

    Thank you,
    Any help for the first point?

    Regards,
    SATYA


    Originally posted in cdnusers.org by satya1234
    • Post Points: 0
  • Mon, Jun 4 2007 9:05 PM

    • archive
    • Top 75 Contributor
    • Joined on Fri, Jul 4 2008
    • Posts 88
    • Points 4,930
    RE: How to get the padstack's informations? Reply

    Regarding your first point: "How to get the padstack's information..."

    You can run the report command from a Dos Prompt or Unix Shell on the padstack file (.pad) with the following command: report -v pad .  This report does not require an special SKILL script because it is already part of the standard report tool.

    Here is an example:

    Command typed on the Dos Prompt: report -v pad pad30cir20d.pad pad30cir20d.rpt

    Below report is : pad30cir20d.rpt
    |------------------------------------------------------------------------------|
    |                         PADSTACK  DEFINITION  REPORT                         |
    |                                                                    Page   1  |
    |------------------------------------------------------------------------------|
    |  E:/pad30cir20d.pad                                                          |
    |  dimensions in mils                                Mon Jun 04 22:56:04 2007  |
    |------------------------------------------------------------------------------|
    | Pad name: PAD30CIR20D              Type NON-VIA        Inner-pads OPTIONAL   |
    |- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - |
    |    subclass or   | pad  |outline  |   size    |  offset   |  flash  |  shape |
    |mask-type or drill| type |geometry | wdt | hgt |  x  |  y  |  name   |  name  |
    |- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - |
     TOP                PAD    CIRCLE       30    30     0     0                   
                        T-REL  CIRCLE       58    58     0     0                   
                        A-PAD  CIRCLE       58    58     0     0                   
     - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 
     internal_pad_def   PAD    CIRCLE       25    25     0     0                   
                        T-REL  CIRCLE       53    53     0     0                   
                        A-PAD  CIRCLE       53    53     0     0                   
     - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 
     BOTTOM             PAD    CIRCLE       30    30     0     0                   
                        T-REL  CIRCLE       58    58     0     0                   
                        A-PAD  CIRCLE       58    58     0     0                   
     - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 
     TOP-SOLDER-MASK    PAD    CIRCLE       50    50     0     0                   
     - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 
     BOTTOM-SOLDER-MASK PAD                  0     0     0     0                   
     - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 
     TOP-PASTE-MASK     PAD                  0     0     0     0                   
     - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 
     BOTTOM-PASTE-MASK  PAD                  0     0     0     0                   
     - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 
     TOP-FILM-MASK      PAD                  0     0     0     0                   
     - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 
     BOTTOM-FILM-MASK   PAD                  0     0     0     0                   
    |------------------------------------------------------------------------------|
    |    DRILL:                                                                    |
    |- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - |
    |      hole     |  plating  |      display/plot        size      | hole offset |
    |      size     |   type    |   figure  |character| wdt  | hgt   |  x   |   y  |
    |- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - |
          20         PLATED      CROSS                     20      20      0      0
    |------------------------------------------------------------------------------|
    |------------------------------------------------------------------------------|
    |   total padstack definitions 1                                               |
    |------------------------------------------------------------------------------|

    Hope this helps,
    Mike Catrambone
    UTStarcom, Inc.


    Originally posted in cdnusers.org by mcatramb91
    • Post Points: 0
  • Mon, Jun 4 2007 9:45 PM

    • archive
    • Top 75 Contributor
    • Joined on Fri, Jul 4 2008
    • Posts 88
    • Points 4,930
    RE: How to get the padstack's informations? Reply

    Thank you..

    SATYA

    ATS ECAD TECH Pvt Ltd


    Originally posted in cdnusers.org by satya1234
    • Post Points: 0
Page 1 of 1 (5 items)
Sort Posts:
Started by archive at 03 Jun 2007 10:48 PM. Topic has 4 replies.