Home > Community > Forums > PCB Design > Need help tuning diff pairs---will PAY

Email

* Required Fields

Recipients email * (separate multiple addresses with commas)

Your name *

Your email *

Message *

Contact Us

* Required Fields
First Name *

Last Name *

Email *

Company / Institution *

Comments: *

 Need help tuning diff pairs---will PAY 

Last post Tue, Jun 18 2013 9:47 AM by Ejlersen. 4 replies.
Started by pitbull107 16 Jun 2013 05:11 AM. Topic has 4 replies and 661 views
Page 1 of 1 (5 items)
Sort Posts:
  • Sun, Jun 16 2013 5:11 AM

    • pitbull107
    • Top 100 Contributor
    • Joined on Thu, Jul 17 2008
    • Berkshire, NY
    • Posts 64
    • Points 1,185
    Need help tuning diff pairs---will PAY Reply

     Hi. In another post I was asking about diff pair tuning.....well....I just cannot figure how to do it. I am willing to pay someone to take the brd, tune the diff pairs and send it back with detailed explanation how it was done.  It HAS to be in either 16.0 or 16.5 XL

    I need this done by Tuesday 6/18 LATEST.

     

    PS This will probably be gravy for someone who knows their stuff.

    • Post Points: 20
  • Tue, Jun 18 2013 6:06 AM

    • steve
    • Top 10 Contributor
    • Joined on Fri, Jul 18 2008
    • Woking, Surrey
    • Posts 1,243
    • Points 20,215
    Re: Need help tuning diff pairs---will PAY Reply

    You could always try using Route - Phase Tune which means you can add a small bump to each half individually to try and help meet the phase. Look at the Options menu for values for the size of the bump.

    • Post Points: 20
  • Tue, Jun 18 2013 6:20 AM

    • pitbull107
    • Top 100 Contributor
    • Joined on Thu, Jul 17 2008
    • Berkshire, NY
    • Posts 64
    • Points 1,185
    Re: Need help tuning diff pairs---will PAY Reply

     I have route-> delay tune, but that has no options for "bumps", at least in 16.0.  I saw that in the doc you uploaded. Can't find it.

    But anyway, I got the lengths tuned after the EE relaxed the delta from 5mil to 100mil and I fiddled with the constraint manager  until I got the etch lengths to make sense. (Had a dream about them last night.......)

    • Post Points: 35
  • Tue, Jun 18 2013 6:26 AM

    • steve
    • Top 10 Contributor
    • Joined on Fri, Jul 18 2008
    • Woking, Surrey
    • Posts 1,243
    • Points 20,215
    Re: Need help tuning diff pairs---will PAY Reply

    You'd need at least 16.5 to see Phase Tune.

    • Post Points: 5
  • Tue, Jun 18 2013 9:47 AM

    • Ejlersen
    • Top 10 Contributor
    • Joined on Mon, Jul 28 2008
    • Aalborg, Copenhagen
    • Posts 569
    • Points 10,080
    Re: Need help tuning diff pairs---will PAY Reply

    Hi

     

    I would just add that updating to 16.6 with the newest quarterly incremental release would give you a prototype of the new phase tune that will be coming up in a later quarterly update.

    You can see a bit of it in the movie below, although the spoken language is Danish, you could move forward to 6 minutes and get the meaning of this. My prediction is that the complete timing vision and tuning environment will make routing and understanding timing constraints so much simpler going forward.

    http://www.youtube.com/watch?v=MZceOKd2sIQ

    Hope you can use it for inspiration. 

     

    Best regards

    Ole

    Best regards Ole
    • Post Points: 5
Page 1 of 1 (5 items)
Sort Posts:
Started by pitbull107 at 16 Jun 2013 05:11 AM. Topic has 4 replies.