Home > Community > Forums > Custom IC Design > Cadence 6.1.0 NCSU kit error :ERROR (OSSHNL-116)

Email

* Required Fields

Recipients email * (separate multiple addresses with commas)

Your name *

Your email *

Message *

Contact Us

* Required Fields
First Name *

Last Name *

Email *

Company / Institution *

Comments: *

 Cadence 6.1.0 NCSU kit error :ERROR (OSSHNL-116) 

Last post Tue, Feb 9 2010 5:15 AM by Quek. 1 replies.
Started by kumarghz 09 Feb 2010 04:17 AM. Topic has 1 replies and 3798 views
Page 1 of 1 (2 items)
Sort Posts:
  • Tue, Feb 9 2010 4:17 AM

    • kumarghz
    • Not Ranked
    • Joined on Tue, Feb 9 2010
    • Posts 1
    • Points 20
    Cadence 6.1.0 NCSU kit error :ERROR (OSSHNL-116) Reply

    For Cadence 6.1.0 version and we are getting error such below during simulation. For your information we are using NCSU CDK ver. 1.6.0 beta.

    I believe attached the Techfile (NCSU_ami06) & model (ami06.m) correctly in virtuoso & ADE respectively. Also tried change instance view=symbol.

    error:
    ------------------------------------------------------------------------------------------
    ERROR (OSSHNL-116): Unable to descend into any of the views defined in the view list, 'hspiceD spice cmos_sch cmos.sch schematic', for the
    instance 'M1' in cell 'myinverter'. Either add one of these views to the library 'NCSU_Analog_Parts',
    cell 'pmos4' or modify the view list to contain an existing view.

    End netlisting Feb 5 23:18:54 2010
    ERROR (OSSHNL): Error(s) found during netlisting. The netlist may be corrupt
    or may not be produced at all.
    To generate correct netlist, fix the errors and re-netlist.
    ...unsuccessful.
    -------------------------------------------------------------------------------------------

    Pls guide. Thanks

    regards,
    Kumar

    Filed under:
    • Post Points: 20
  • Tue, Feb 9 2010 5:15 AM

    • Quek
    • Top 10 Contributor
    • Joined on Wed, Oct 14 2009
    • Singapore, 00-SG
    • Posts 1,063
    • Points 16,170
    Re: Cadence 6.1.0 NCSU kit error :ERROR (OSSHNL-116) Reply

    Hi Kumar

    Are you using spectre for simulation? Please check the following:

    a. In your schematic, select instance "M1"
    b. Press "q" to bring up the properties form
    c. Note the libname and cellname. Go to library manager and check if this cell has a "spectre" view or the view for your simulator. E.g. if you are using hspiceD simulator, it should have a "hspiceD" view.

    Assuming that you are using spectre, if "spectre" view is present for this cell, please go to "Setup->Environment" in ADE menu and modify "switch view list" and "stop view list" as follows:

    switch view list : spectre cmos_sch cmos.sch schematic veriloga
    stop view lis : spectre

    You mentioned that you are using Cadence 6.1.0. I am not sure if you are really meant "IC6.1.0" or if you are just refering to IC6.1. For your information, there are a lot of new features in IC614 and so it would be great if you can give it a try.

    Best regards
    Quek

    • Post Points: 5
Page 1 of 1 (2 items)
Sort Posts:
Started by kumarghz at 09 Feb 2010 04:17 AM. Topic has 1 replies.