Home > Community > Tags > 6.1.5
 
Login with a Cadence account.
Not a member yet?
Create a permanent login account to make interactions with Cadence more conveniennt.

Register | Membership benefits
Get email delivery of the Cadence blog (individual posts).
 

Email

* Required Fields

Recipients email * (separate multiple addresses with commas)

Your name *

Your email *

Message *

Contact Us

* Required Fields
First Name *

Last Name *

Email *

Company / Institution *

Comments: *

6.1.5

  • Driving an internal node several heirarchical layers down...

    All, First, an apology. I am new to ADE XL and spectre, coming from hspice and MICA, so if I am asking a really obvious question, please pardon my ignorance. However, in my defence, this is stumping the local ADE XL expert. I have tried various searches of the forums and google without luck. So here...
    Posted to Custom IC Design (Forum) by deklein on Fri, Mar 14 2014
  • Schematic Editor: Make cell EDITABLE automatically

    Hi, I am using virtuoso 6.1.5 I have a schematic editor open with a cell in readOnly mode. Is it possible to configure cadence so that the cell automatically switches into EDIT mode whenever the user tries to change something on the schematic? Eg, I do not want to go to "File -- Make Editable"...
    Posted to Custom IC Design (Forum) by NiallDuncan on Fri, Jan 24 2014
  • meassuring delay in viva

    dear all, I would like to measure delay on signal "gap" simulated on two temp -40 and 125 with "trigger" option like: dly_fr=delay( v("gap") 0.75 1 "falling" v("gap") 0.75 2 "rising" 1 1 t "trigger") I am getting results like: time...
    Posted to Custom IC Design (Forum) by jerry124 on Tue, Nov 26 2013
  • Force ams netlister to skip ports/pins

    Hello, Andrew! I want to skip several ports of the symbol during schematic netlisting for ams simulation. How can I do it? (As far as know there is a kind of property to be added to the pin) Netlister revision: // AMS netlist generated by the OSS based AMS netlister // IC subversion: IC6.1.5-64b.500...
    Posted to Custom IC Design (Forum) by Runner on Sat, Aug 24 2013
  • Re: Noise simulation in Cadence

    Thank you so much Andrew! It helps a lot! However, I'm still not very sure what to probe if I want to measure the output noise current. You mentioned "a voltage source/iprobe", then what is 'iprobe'? My test circuit is shown below. I want to test the thermal current noise "ID...
    Posted to Custom IC Design (Forum) by EthanRFIC on Mon, Jul 15 2013
  • An urgent problem with the design rule check using Assura

    When I use Assura to do the design rule check after I have done layout using the C35B4 technology in Cadence, there is always a following probleme: [1] #INFO: C35B4/C35B3 ASSURA DRC DECK(REV9 DATE 26-Apr-2011) Last modified 15-Jun-2012. does anyone know why? Thank you advance for you response.
    Posted to Custom IC Design (Forum) by UUinfini on Fri, Jun 14 2013
  • ADEXL: Plot vs save

    Hi, Why can you check plot and not check save in ADEXL? Shouldn't it be automatically saved when you plot? If this is the case, the save checkbox should be automatically checked and/or disabled. Or have I misunderstood the meaning of plot vs save?
    Posted to Custom IC Design (Forum) by Tobben24 on Fri, Nov 30 2012
  • Continue simulation after it is finished

    Hi, Is it possible to continue a simulation after it is finished? I mean, if you run a simulation and after it is done you see on the plot that you should have runned it a few us longer.
    Posted to Custom IC Design (Forum) by Tobben24 on Thu, Nov 29 2012
  • ADEXL: Change config file and re-run simulation automatically

    Hi, I want to do the following 5 times with a new schematic view every time: 1. Run a simulation 2. Switching schematic view on one cell in the config file and re-run Any one have a good advice on how to do this in ADEXL? I could create 5 tests with 5 different config files? Or is a Cell View restricted...
    Posted to Custom IC Design (Forum) by Tobben24 on Tue, Nov 27 2012
  • ADEXL switch default ocean script editor

    Hi, When I want to edit an oscean script in ADEXL Setup tab(E button), the script is opened in emacs. How can I change this to another program, ie. vim?
    Posted to Custom IC Design (Forum) by Tobben24 on Mon, Nov 26 2012
Page 1 of 2 (11 items) 1 2 Next >