Home > Community > Blogs > RF Design > measuring bipolar transistor ft with fixed base collector voltage
 
Login with a Cadence account.
Not a member yet?
Create a permanent login account to make interactions with Cadence more conveniennt.

Register | Membership benefits
Get email delivery of the RF Design blog (individual posts).
 

Email

* Required Fields

Recipients email * (separate multiple addresses with commas)

Your name *

Your email *

Message *

Contact Us

* Required Fields
First Name *

Last Name *

Email *

Company / Institution *

Comments: *

Measuring Bipolar Transistor ft with Fixed Base-Collector Voltage

Comments(2)Filed under: RF design, bipolar transistor, RFIC, Virtuoso, ViVA, RF Simulation, ADE, RF, analog, measuring bipolar transistor ft, testbench, Vbc, transistor ft, Schaldenbrand, fixed base-collector voltage, parametric analysisRecently I had a question from reader. He asked a good question: "How do you to measure a bipolar transistor's ft when the base-collector voltage, Vbc, is fixed?" Attached is a modified version of the testbench that allows a user to measure ft with a fixed Vbc. While the aesthetics are not as pleasing as the original testbench, it does the job.

The testbench is shown in Figure 1. The base of the bipolar transistor, the DUT, is grounded.  The collector of the transistor is connected to a dc source, VBC, which is used to set the base-collector voltage of the transistor. The emitter is connected to a current source that sets the bias current, IE. An additional supply, VBE, is included to assure the base-emitter junction is always forward biased. For these tests, the dummy power supply voltage, VBE, is set to 5V.

Figure 1: Ft Testbench modified for fixed Vbc

To measure the ft, use the same methodology previously described:

1.       Run a dc operating point analysis and save the collector current

2.       Run an ac analysis,  sweep the frequency beyond the maximum value of ft

     a.       In this case, the ac sweep was from 1Hz to 10GHz

     b.      Save the base and collector currents

3.       Use the Virtuoso ViVA waveform calculator to measure the ac beta of the transistor

     a.       The ac beta is ic/ib, where ic and ib are the ac currents

4.       Use the Virtuoso ViVA waveform calculator cross() function to measure the ft

     a.       Measure the frequency where the value of the ac beta=1, or 0dB

5.       In Virtuoso Analog Design Environment, ADE, setup a parametric plot to sweep the emitter current

     a.       In this case the emitter current was swept from 100nA to 10mA

6.       Run Parametric Analysis

7.       Plot the collector current and the ft when the analysis completes

8.       Use the Y vs Y option to plot the ft vs the collector current

Shown below is an example of the ft curves for the NPNupper transistor model used in the rfLib. The ft was measured for current sweeps using different values of Vbc: 0.5V, 1.0V, and 1.5V. As you can see, increasing the base-collector voltage delays the onset of saturation and allows the transistor to achieve higher ft.

Figure 2: ft vs Ic for a fixed Vbc

Please let me know if this post was useful, if you have any questions, or comments.

Art Schaldenbrand

Comments(2)

By Per Olaf Pahr on September 11, 2012
Very useful test bench. Just a minor comment on the name "VBE" chosen for the 5 volt dummy supply. Let us call it VEE and reserve the VBE name for the bipolar device's voltage difference VBE = VB - VE (e.g. 0 V -(-0.7 V) = 0.7 V. The NPN is biased with an emitter current, so the voltage absorbed by the current source is VEE - VBE.

By Winfield Hill on December 2, 2012
You can generate the same set of curves, and others quickly in a spreadsheet, by using the model's SPICE parameters.  We know that  fT = 1 / 2pi ( CJE VT/Ic + tau-F ), and we get the transit time tau-F from the SPICE-engine formula tau-F = TF * [ 1+ XTF * (Ic/Ic+ITF)^2 * exp (Vbc/1.44*VTF) ] entered into the spreadsheet cells.  CJE, TF, ITF, VTF and XTF are the SPICE parameters.

Leave a Comment


Name
E-mail (will not be published)
Comment
 I have read and agree to the Terms of use and Community Guidelines.
Community Guidelines
The Cadence Design Communities support Cadence users and technologists interacting to exchange ideas, news, technical information, and best practices to solve problems and get the most from Cadence technology. The community is open to everyone, and to provide the most value, we require participants to follow our Community Guidelines that facilitate a quality exchange of ideas and information. By accessing, contributing, using or downloading any materials from the site, you agree to be bound by the full Community Guidelines.